New do-dads

Renault & Alpine General Discussion

Moderators: eastlmark, BIG_MVS, phildini, Test Moderator, Alpineandy

User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

New do-dads

Postby clee » Thu Aug 04, 2005 6:34 pm

My car has a BBR 'chip' ,it looks like a chip ,smells like a chip ,put salt'n'vineger on it .It is a bit of electronics that alters the factory settings anyway ,supposedly running 12 psi .What are the implications for further mods :?: Looking to upgrade Turbo ,can I just bolt this on and a gauge ,or do I need swap the BBR out as well and put a boost adjuster in its place :?
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Thu Aug 04, 2005 7:22 pm

Get me a picture of the inside of the ecu....

Is there a cluster of chips and the top left has the BBR sticker on it?

Has it been piggyback soldered in or does it look like original fittment?

The reason why I ask is I heard that BBR just adjusted the actuator and turned the boost up, and stuck a sticker on the chip. 12psi is within the factory standard map limits, so there is no gains from 'remapping' at that level. If they could have remapped it you'd expect it to be 14psi, and remove the boost cut.

If it is 'chipped' then putting a bigger turbo on isnt a problem, you would still need to turn the boost up to get the full potential. As I said above, don't know if the BBR mod would have removed the boost cut.
Image
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Thu Aug 04, 2005 7:44 pm

Its a new chip or sticker :lol: I'll have another look but from memory the chip with the sticker is bot right .It might not matter as I could just regard it as being standard :?: Was just thinking aloud ,if its not a standard setup to start with how do you know if the new bits are behaving as they should ,are they adversely affected by the previous mods ? As long as the previous items don't degrade the factory settings it should be ok.The BBR thing is not an addition ,it's a replacement ,so worst case probably does nothing .
I'll take a piccy of the unit .
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Thu Aug 04, 2005 9:58 pm

I say top left, you say bottom right - depends which way we're both looking at it! :lol:

Its a shame, I sold my last standard GTA ecu a few months back, you could have tried it to see if there were any differences...
Image
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Fri Aug 05, 2005 12:57 pm

clee wrote:Have had a look in the ECU but can't see anything like a black box,
though one of the `chips' does not look like the rest.I have taken some piccies, they're not to clear ,but shows the placement ,can't post it here tho.Pretty sure that this is the item in question as the code on it reads
BK48 RNV6TPH1 .The conversion was tested by BBR May 98 (found an invoice in the history file ).



Image

It looks different to the others which are blue enamel looking, so think its not just a sticker
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Fri Aug 05, 2005 1:36 pm

Thats the one.....see...top left! :lol: That chip is the map chip, so it is different to all the rest. Normally the inside of the circuit boards are sprayed in clear laquer after assembly, so if a new chip has been installed, much of this laquer around the chip would have been broken/removed.

Is strange if it is a new chip, that they only set it to 12psi. It wouldnt have made as much power as their competitor Superchips at the time who set theirs to 14psi.
Image
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Fri Aug 05, 2005 2:03 pm

Sort of bot middle ,SSWest ish :lol: Can I just add to this setup as if it wasn't there .Will the ART ( club discounted :shock: :lol: ) boost upgrade be OK with it :?:
User avatar
User

David Gentleman

Rank

Non Member

Posts

3474

Joined

Thu Apr 15, 2004 8:10 am

Location

Colchester, Essex


Has thanked: 0 time
Been thanked: 0 time

Postby David Gentleman » Fri Aug 05, 2005 2:34 pm

Yes you can...if the chip is real then you should see even more gains. Id reccomend getting a boost gauge sorted so you can check you are running 12psi. Obviously jumping to 14 odd is not going to as much as a gain as someone who was running at 9/10.
Image
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Mon Aug 08, 2005 12:59 pm

BBR my asp :evil:
Glad I didn't pay for it :lol:
Now it might not be down to the 'chip' ,maybe there's something else amiss ,but have fitted a boost gauge and got the following .
Connected to DV vac pipe, -10 & 8.5 PSI, in place of std gauge
9 psi :evil: :evil:
User avatar
User

clee

Rank

Non Member

Posts

10431

Joined

Fri May 28, 2004 11:58 am

Location

Derbyshire


Has thanked: 54 times
Been thanked: 104 times

Postby clee » Mon Aug 08, 2005 5:06 pm

Now I'm :? Have done nothing more than fit the manual boost controller ,left it wide open and now getting 12 psi .The only extra bit is 15 cm of extra pipe to the boost controller .


  • Advertisement

Who is online

Users browsing this forum: No registered users and 116 guests

Powered by phpBB ® | Renault' and 'Alpine' are trademarks of Renault S.A.S. or its subsidiaries and are used with kind permission of Renault France